Characteristic

Kammprofile gasket (Serrated metal gasket)은 cold rolled metal plate로 만들어 졌으며, 동심 홈을 가지며 효과적인 실링 영역이 최소화되어 실링 효과를 증가시킵니다. Flat한 금속 가스켓은 cold rolled metal plate로 만들어진 모든 금속 가스켓 중 가장 심플하고 경제적인 유형입니다. 이 가스켓은 모든 pipe flange에 광범위하게 사용되며, Valve Bonnets, 고온 및 고압 압력 용기 커버에 사용됩니다.

Performance and technical integrity of the gaskets 신뢰성 검증

Type Acceptance Test

The Type Acceptance Test (TAT) is installed to verify the design, performance and technical integrity of the gaskets and manufacturing plant.

Test Specimens

The dimensions of the test specimens for the different tests were EN 12560-6, Class 300, 4” The dimensions of the flanges in contact with gasket is OD = 154.0mm and ID = 123.8mm. The thickness of the Spiral Wound Gasket is 4.0mm. The thickness of the outer ring was 3.0mm.

Test Equipment

The gasket tests were carried out on the following testing equipment: Below Multifunctional test rigs are TEMES and Fire Safe testing Device.

Test Results

The Kammprofile Gasket passed all test according to Shell Specification MESC SPE 85/300

수압테스트

The Hydraulic Test is to verify the design, performance and technical integrity of the gaskets and manufacturing plant according to ASME B16.5

Test System

The test system is specified in B16.5 clause 2.6 as follows. 2.6 System Hydrostatic Testing Flanged joints and flanged fittings may be subjected to system hydrostatic tests at a pressure of 1.5 times the 38°C (100°F) rating rounded off to the next higher 1 bar (25 psi) increment. Testing at any higher pressure is ASME B16.5-2009 the responsibility of the user, taking into account the requirements of the applicable code or regulation.

Test Specimens

The dimensions of the test specimens for the different tests were ASME B16.20 , 4” Class 300. The dimensions of the flanges in contact with gasket is OD = 154.0mm and ID = 123.8mm. The thickness of the Spiral Wound Gasket is 4.5mm.

Test Results

The Kammprofile Gasket passed the hydraulic test according to ASME B16.5

Style Selection Guide

Metal Core Materials

Covered Layer Materials

High Operating Temperature (HT) Type

캠프로파일 가스켓은 최상의 Load를 견디는 특성을 지닌 Seal입니다. P와 C type은 centering ring(collar)가 없는 type으로 Male & Female과 Tongue & Groove type의 flange에 사용되며 PR, PR1, CR, CR1 type은 flat face와 raised face type의 flange에 사용됩니다. Sealing core는 양쪽 Sealing면에 균일한 Serration이 주어지며 Serration표면 위에 Flexible Graphite, PTFE 또는 HT (E-Graphite+Mica) 등으로 덮어져 있습니다. 이것은 낮은 Seating Stress로 높은 sealing성을 가져다 줍니다. 삼성인더스트리의 캠프로파일은 신뢰성있는 재료와 정밀한 가공을 통해서 제작되어 집니다.

Sizes: Standard sizes are prepared to fit ASME and JIS pipe flanges. Other gasket sizes are also available with EN 12560-6 and EN 1514-6 standard dimensions.